TECHNICAL ARTICLE

Core Steps in Building Cooling Load Calculations

Step-by-step sensible and latent cooling calculations, an office example, hourly diversity, equipment selection and commissioning checks.

1. Cooling load is not equipment capacity or energy use

Cooling load is the heat-removal rate needed at a particular instant to maintain a room's target temperature and humidity. It is measured in W or kW. Daily energy is measured in kWh: 10 kW of load and 10 kWh of energy are different quantities, and must remain distinct in calculation, selection and operating assessments.

The calculation determines more than a required air-conditioner rating. It identifies when and where loads occur, sensible versus latent demand, where outdoor air is conditioned, and how the system behaves at part load.

This guide uses an independent educational office example, not local weather criteria or a specific equipment selection. Hospitals, kitchens, laboratories, data centres and process spaces need additional application-specific assessment.

2. Separate heat gain, room load and coil load

Heat entering a room does not all reach the air immediately. Solar radiation on the floor and radiant gains from occupants can first be stored in surfaces and released later. Instantaneous heat gain and same-hour cooling load are therefore not always equal.

Room load maintains room conditions. Depending on the system, AHU coil load can additionally include outdoor air, fan heat, duct gains and other effects. Combining them without a boundary can inflate capacity.

ASHRAE describes heat-balance and radiant-time-series methods. State how the adopted method treats time-dependent effects: https://handbook.ashrae.org/Handbooks/F25/SI/F25_Ch18/F25_Ch18_si.aspx

Identify whether each table represents the room, fan coil, outdoor-air unit or central cooling plant. Count every component once at the correct boundary.

3. Why sensible and latent loads are separate

Sensible load changes temperature: conduction, solar, lights and many appliances principally contribute to it. Latent load requires moisture removal from people, humid outdoor air, doors and processes.

Qtotal = Qsensible + Qlatent
SHR = Qsensible / Qtotal

An 8 kW sensible/2 kW latent room requires 10 kW total at SHR 0.80. A unit rated at 10 kW total is not necessarily suitable: its sensible and latent outputs at the actual conditions must match.

A unit can cool quickly and stop before removing enough moisture. Review low sensible load, humid weather and part-load operation. Peak total capacity alone does not guarantee humidity control: https://www.trane.com/content/dam/Trane/Commercial/global/products-systems/education-training/engineers-newsletters/airside-design/enews_29_04_082800.pdf

4. Establish boundaries and architectural inputs

Divide the building into rooms/zones with distinct use, orientation and schedules. A west-facing meeting room differs from an internal office; a top-floor room has roof exposure that an intermediate floor may not.

For each room, record area, height, volume and code; exterior wall/roof/window/floor/adjacent-space areas; orientation, shading and glazing; construction, U-values and thermal mass; people/activity/hourly schedules; lighting/equipment and utilisation; indoor temperature/moisture targets and outdoor air; doors, infiltration, exhaust and pressurisation.

Subtract glazing from opaque wall area. Do not count a window as both glass and wall, or treat a partition between similar conditioned rooms as external. Use the actual boundary temperature for a different adjoining space.

5. Outdoor and indoor design conditions

A city and one temperature are insufficient. Record dry bulb, suitable moisture data, altitude/pressure, solar conditions, exceedance criterion and adopted weather source.

Do not combine maximum dry bulb and maximum moisture from unrelated hours into one unrealistic weather state. Where needed, assess temperature-peak and humidity-critical scenarios separately.

The example's 25 °C room and 0.010 kg water/kg dry air are assumed educational targets, not universal requirements. Relative humidity and humidity ratio differ: the same RH at different temperatures represents different moisture contents.

Use local pressure for psychrometrics. Altitude changes density; sea-level approximations can distort flow and load at high elevations.

6. Wall, roof and glazing conduction

Qconduction = U × A × ΔT

With U in W/(m²·K), area in m² and difference in K, the result is W. Glazing at U=1.8, area 20 m² and 10 K difference has 360 W conductive gain. This excludes solar transmission.

For opaque surfaces, solar heating, colour and thermal storage matter. A final hourly load calculation cannot always use outdoor dry bulb alone in U×A×ΔT. Apply the adopted effective-temperature, surface heat-balance or time-dependent method.

Roof heat gain and room load may peak at different times. Layers and schedules matter as well as insulation. The effective differences below are assigned educational inputs, not dynamic-model results.

7. Solar gain through glazing

Solar gain depends on area, orientation, hour, irradiation, SHGC and shading. A simplified preliminary expression is:

Qsolar ≈ Aglass × I × SHGC × Fshade

I is incident irradiation on the glazing plane in W/m². Do not apply horizontal irradiation indiscriminately to vertical façades. SHGC describes admitted solar energy; U-value describes conduction.

For 20 m², 450 W/m², SHGC=0.40 and an independent external-shading factor 0.70, gain is 2,520 W. This is instantaneous gain for teaching. Final room load requires radiant storage and hourly treatment.

If shading is already included in glass data or the model, do not apply it twice. Internal blinds, external fins and neighbouring buildings differ physically. Model real geometry, especially low-angle western sun.

8. People, lights and equipment

Use sensible/latent person gains appropriate to activity and indoor conditions, with peak and hourly occupancy separately recorded. Sedentary and active people differ.

For this example, 10 people at assumed 75 W sensible and 55 W latent each produce 750/550 W. These are teaching assumptions, not fixed values for every office.

Use installed lighting power or verified W/m². Consider schedules, drivers/ballasts and heat transfer to the room versus return plenum. Do not duplicate software corrections manually.

Equipment nameplate power is not necessarily room heat gain. Consider use/load factors, standby consumption and heat rejected elsewhere. Computers, printers, motors, kitchens and servers have different profiles. A blanket high W/m² allowance without an equipment list can oversize the system.

9. Sensible ventilation and infiltration load

Ventilation is controlled outdoor-air supply; infiltration is uncontrolled flow through leaks and doors. They are distinct, but assigning the same air to both counts it twice.

Qsensible,air = ρ × V̇ × cp × (Toutdoor − Tindoor)

With density kg/m³, flow m³/s and cp kJ/(kg·K), output is kW. At ρ=1.20, cp=1.006 and 0.10 m³/s from 35 to 25 °C, load is about 1.207 kW. The airflow equals 360 m³/h.

Determine ventilation from use, people, area and adopted requirements. The example's 360 m³/h is a given input, not an adequacy recommendation for every ten-person office.

Infiltration depends on airtightness, wind, doors, exhaust and pressure. Justify both a zero-infiltration assumption in a pressurised building and any large fixed air-change allowance.

10. Latent outdoor-air load and enthalpy

Qlatent,air ≈ ṁdry air × hfg × (woutdoor − windoor)

Using w in kg water/kg dry air, hfg in kJ/kg and dry-air mass flow in kg/s gives kW. For approximate mass flow 0.12 kg/s, hfg=2,500 and Δw=0.006, latent load is 1.80 kW.

Constant properties and approximate mass flow simplify the example. Detailed work requires consistent specific volume, dry-air flow and psychrometric states. '60% outdoor humidity' alone cannot define latent duty.

An alternative total-load check is:

Qtotal,air = ṁdry air × (houtdoor − hindoor)

Do not add this to sensible/latent loads already calculated for the same air. These are alternative representations of the same energy change. Approximate coefficients may produce small discrepancies; use one consistent psychrometric method for final design. https://trace3dplus.help.trane.com/design_psychrometrics.html

11. How heat recovery changes outdoor-air duty

Recovery can precondition outdoor air, but one efficiency factor cannot reduce every component. Temperature and moisture effectiveness differ and depend on product, flow and entering conditions.

Sensible-only recovery may reduce temperature difference without reducing moisture equally. Latent load does not automatically disappear. Check bypass, stream balance, actual performance and fan energy.

If the model already uses the recovered air state at coil entry, do not reduce outdoor load again. Label the boundary before or after recovery.

12. Step-by-step 100 m² office example

This simplified example teaches components and units. Assigned opaque-surface effective differences and solar gain treated as load do not replace hourly HB/RTS calculations. It excludes infiltration, recovery, fan/duct gains and other rooms.

InputEducational assumption
Floor area and people100 m²; 10 people
Indoor/outdoor dry bulb25/35 °C
Indoor/outdoor humidity ratio0.010/0.016 kg/kg dry air
Net opaque wall60 m²; U=0.60; effective difference 14 K
Roof100 m²; U=0.40; effective difference 20 K
Glass20 m²; U=1.80 W/(m²·K)
Glazing irradiation and factors450 W/m²; SHGC 0.40; shade 0.70
Lighting8 W/m²; operating factor 0.90
Equipment1,200 W; room-gain/use factor 0.75
Outdoor air0.10 m³/s; density approximately 1.20 kg/m³

Wall: 0.60×60×14=504 W. Roof: 0.40×100×20=800 W. Glass conduction: 1.80×20×10=360 W. Solar: 20×450×0.40×0.70=2,520 W. People: 10×75=750 W sensible and 10×55=550 W latent. Lighting: 8×100×0.90=720 W. Equipment: 1,200×0.75=900 W.

ComponentSensibleLatent
Wall0.504 kW0
Roof0.800 kW0
Glass conduction0.360 kW0
Simplified solar effect2.520 kW0
People0.750 kW0.550 kW
Lighting0.720 kW0
Equipment0.900 kW0
Room subtotal6.554 kW0.550 kW
Untreated outdoor air1.207 kW1.800 kW
Preliminary combined total7.761 kW2.350 kW

Room subtotal is 7.104 kW; the combined preliminary total is 10.111 kW, at SHR approximately 0.768. This represents a simplified boundary containing the room and untreated outdoor air, not a definitive device or central-coil capacity.

If a separate AHU conditions outdoor air to room conditions, do not add the complete outdoor load again to the fan coil. Evaluate AHU duty and its supply contribution separately. Direct untreated delivery produces a different room-equipment requirement.

13. From sensible demand to supply airflow

V̇supply = Qsensible,room / [ρ × cp × (Troom − Tsupply)]

At room sensible load 6.554 kW, room 25 °C and assumed supply 14 °C, approximate airflow is 0.494 m³/s, or 1,777 m³/h. This is total supply estimated from sensible duty, not outdoor ventilation demand.

Check the assumed 14 °C against diffuser placement, draught, condensation, moisture removal and product limits. Determine supply humidity ratio for latent duty separately; temperature arithmetic does not establish a complete psychrometric solution.

Do not confuse supply flow, outdoor flow and coil capacity. Mixed-air entering state depends on return and outdoor states; leaving state depends on equipment and control.

14. Room peaks versus building peak

Rooms peak at different times. Size terminals for their own peaks and central systems for simultaneous loads.

TimeEast roomWest roomSimultaneous total
10:008 kW4 kW12 kW
15:005 kW9 kW14 kW

Adding individual peaks gives 17 kW; the maximum among these two shown hours is 14 kW. It is not a final building result without all hours, days and rooms.

Diversity must come from schedules and credible scenarios, not an unexplained reduction factor. Fully occupied events can coincide with other peaks.

15. Equipment-selection checks

Catalogue capacity may use different outdoor, indoor dry/wet-bulb, airflow or water conditions. Verify actual selection output, including sensible/latent capacity, minimum modulation, sound and distribution.

For fan coils check water flow/loss; for AHUs check entering/leaving states, fan heat and pressure; for DX use manufacturer corrections.

Oversizing can shorten runtime and worsen humidity. Verify uncertain inputs and state justified margins separately. Avoid adding allowances to every component and then a second large equipment margin.

16. Validate software inputs

Software does not remove the need to verify orientation, SHGC, shading, schedules, outdoor-air definitions and equipment. Detailed output can simply describe incorrect inputs in detail.

Match model zones to HVAC zones and check net walls, roof exposures and adjoining temperatures. Understand treatment of lighting-to-plenum gains and system-level ventilation.

Heat-balance background: https://energyplus.net/assets/nrel_custom/pdfs/pdfs_v24.2.0/EngineeringReference.pdf

Independently hand-check a representative room. It need not exactly match a dynamic model; investigate large differences by component. Total kW or W/m² alone may conceal a load assigned to the wrong boundary.

17. Common errors and consequences

Sizing from area alone: W/m² can cross-check, but cannot represent orientation, glass, use and ventilation.

Using glazing U for solar: U and SHGC describe different effects.

Ignoring outdoor latent load: Temperature may be correct while humidity remains high.

Adding all room peaks: Unrelated-hour maxima do not establish central simultaneous demand.

Applying shading or recovery twice: Duplicated reductions can understate capacity; identify each physical correction.

Misplacing fan heat: Fan position before/after the coil affects leaving conditions. Count its heat once at the right boundary.

18. Calculation report and commissioning checklist

Provide room sensible/latent demand, peak hour, outdoor flow and system-level transfers so another engineer can follow the result. Identify calculations affected by architectural or equipment changes.

Record weather/local pressure, indoor targets/schedules, net surfaces/orientation/glass/shading, realistic people/equipment, separate sensible/latent terms, ventilation/infiltration without duplicates, room/AHU/plant boundaries, hourly simultaneous plant demand, actual-condition selection and part-load temperature/moisture control.

At commissioning, measure outdoor and total supply flows, air states and settings, recording occupancy and weather. A mild-day temperature measurement does not prove peak capacity; interpret it alongside design and performance data.

19. Sources and scope

Examples use assumed surface differences, people gains and operating factors. Obtain final building loads from the adopted method and verified inputs.

Verify applicable standards, special-use requirements and product selections. A good calculation explains not only total capacity but its time, location and sensible/latent distribution.

← All articlesTechnical feedback →