TECHNICAL ARTICLE

Flow and Pressure Checks for Fire Pump Selection

Fire-pump demand, differential and maximum pressures, storage, suction, drivers and acceptance testing with examples.

1. Fire-pump selection starts with hydraulic demand

A fire pump is part of a water supply that must reliably deliver the protected system's design flow and pressure. Multiplying building area by a factor, or adding the flow of every installed sprinkler, is not a valid selection method. Begin with hydraulic demand established under the adopted design standard and identify its reference point.

Determine simultaneous sprinkler, hose-reel, hydrant and other demands from project criteria. Adding another system without identifying the hose allowance can double-count demand; omitting genuinely simultaneous consumption can undersize the supply.

This guide explains selection logic. Its examples are not fire-design criteria. Record the standard edition, local requirements and authority-approved basis at the beginning of the report.

2. Data required before selection

Document all scenarios and their flow/pressure demands; reference points and terminal minimum pressures; critical-path elevations and pipe/fitting/device losses; minimum water-source level or flow-test data; suction conditions and pump type; maximum static supply pressure and component ratings; and power, controls, testing and maintenance arrangements.

Use actual internal diameters for the installed material. Obtain backflow preventer, alarm valve, check valve and strainer losses from product data. If demand is already given at the pump flange, do not add upstream-calculated distribution losses again.

3. Reading the demands of different systems

The operating sprinkler area and protection criteria come from the adopted standard or listed application. Flow develops together with node pressures; nominal discharge multiplied by head count does not solve the network.

Distinguish sprinkler discharge and required supplementary consumption. Required external fire flow and the sprinkler calculation's hose allowance are not necessarily the same. NFPA discusses the distinction: https://www.nfpa.org/news-blogs-and-articles/blogs/2022/03/22/calculating-the-required-fire-flow

Calculate each scenario separately. The highest-flow scenario may not require the highest pressure. The pump curve must meet all applicable demands; combining unrelated maximum values into one pair can conceal important conditions.

4. Required differential pressure

Using consistent reference boundaries:

Δppump = pterminal + Δpelevation + Δppipe + Δplocal + Δpdevices − pavailable,suction

Terminal pressure is required at the discharge point. Elevation contributes approximately ρgΔz: one metre of water is about 9.81 kPa or 0.0981 bar. Evaluate friction and device losses at demand flow, and use suction pressure under the same condition.

An open fire-water discharge differs from a closed heating circuit, where elevation effects balance. Do not ignore building height by copying a circulation-pump calculation.

5. Independent flow and pressure example

Assume 90 m³/h demand, 1.50 bar terminal requirement, 30 m rise, 1.20 bar pipe friction, 0.60 bar local/device losses and 0.30 bar available suction pressure at demand. These are educational inputs, not mandatory standard values.

ComponentPressure contribution
Terminal requirement1.50 bar
30 m elevation2.943 bar
Pipe friction1.20 bar
Local/device losses0.60 bar
Available suction pressure−0.30 bar
Required pump pressure rise5.943 bar

The illustrative duty is about 90 m³/h at 5.94 bar differential pressure, approximately 60.58 m water head. Verify it against the approved fire-pump curve; do not turn this into an ordinary circulation-pump selection.

If 0.30 bar is only an estimate, selection remains incomplete. Verify minimum tank level or water-supply performance at demand flow. Static mains pressure cannot be assumed available during discharge.

6. Read the entire pump curve

Rated duty, shutoff pressure and high-flow behaviour require separate checks. Identify the exact impeller/speed curve, driver power and product approval; the model name alone is insufficient.

If an illustrative pump produces 7.50 bar at zero flow and maximum suction pressure is 1.00 bar, discharge can reach 8.50 bar. Check this against component limits, especially at lower elevations. A 5.94 bar duty requirement does not limit every system pressure to that value.

Verify performance and installation requirements in the adopted edition. NFPA 20 is a principal reference; do not mix numerical limits from different standards: https://www.nfpa.org/product/nfpa-20-standard/p0020code?order_src=C900

7. Suction conditions and pump type

The source level relative to the pump matters. A pump intended for positive suction may be unsuitable for lifting from a lower tank. Select pump type with source level and permitted installation arrangement.

NFPA explains type selection where water is below the pump: https://www.nfpa.org/news-blogs-and-articles/Blogs/2021/04/02/Fire-Pump-Types?ht-comment-id=8105146

Check suction diameter, flow approach, valves, fittings, trapped air and available net positive suction head under the relevant guide. An air pocket or poor connection can impair performance despite a correct discharge calculation. Coordinate usable tank volume, low-water level and vortex prevention with drawings.

8. Main, standby and jockey pumps

Determine duty/standby arrangements and power sources from project requirements. Electric and diesel options require reliability and installation assessment; one arrangement is not universal.

The jockey pump maintains pressure against small leaks and pressure changes. It does not replace the main fire pump. Excessive jockey capacity or incorrect setpoints can delay main-pump starting. Select flow and settings from applicable rules and actual leakage behaviour.

Document setpoints alongside static pressure, pump curves and start sequence. Fire-pump stopping logic must follow fire-protection requirements rather than ordinary domestic booster logic.

9. Design testing and maintenance facilities

Provide test-water routes, flow measurement and safe discharge when selecting the pump. Verify source capacity and access; an undersized test connection added later can prevent proper acceptance testing.

Coordinate room access, ventilation, drainage, driver servicing and power. Diesel fuel and exhaust arrangements require their own compliant design. Meeting paper demand alone does not establish reliable operation.

Record suction/discharge pressures, measured flow, speed, driver data and test points, including water level and valve configuration. Compare with the manufacturer curve and acceptance requirements using consistent references.

10. Checklist and common errors

Check demand reference, simultaneous consumption and hose allowance, minimum source performance at flow, elevation and losses counted once, all demand scenarios, maximum suction/shutoff pressures, suction arrangement and pump type, driver/controls, test access and drainage.

Common errors include nameplate-only selection, using static pressure during flow, omitting elevation, ignoring maximum pressure and treating the jockey pump as a main pump. An arbitrarily oversized pump does not repair missing evidence.

11. Verify the water tank separately

Adequate pump flow does not prove sufficient duration. At an illustrative 90 m³/h demand for an assumed 60 minutes, arithmetic water demand is 90 m³. The assumed duration is not a standard recommendation: actual duration depends on hazard, simultaneous demands and adopted criteria.

Usable volume differs from geometric volume because of dead storage, minimum suction level and other reserved uses. Confirm whether refill can count under the applicable design basis; uninterrupted mains refill cannot be assumed universally.

Assess service during compartment maintenance, low-level alarms and water access to the suction inlet. Establish vortex prevention and minimum submergence from the accepted design/product requirements.

12. Make the selection package auditable

Identify speed, impeller diameter and approval on the curve. Rated-point adequacy does not establish maximum low-flow pressure or other required test points. Compare every component's working rating with maximum suction plus pump pressure rise. Any pressure-control arrangement must comply with fire standards and product approval.

Coordinate electrical supply/controls or diesel fuel/cooling/exhaust. Set start sequences under the approved operating scenario. Building automation does not replace dedicated pump controls and local alarms.

Acceptance records must include flow, suction and discharge pressures, speed and driver information. Do not confuse the discharge gauge reading with net pump pressure rise. Include source and drainage capacity in the test plan and prepare ongoing testing/maintenance under applicable operating requirements.

13. Sources and scope

Example flows, pressures and losses teach calculation only. Final selection requires the building's accepted fire-protection basis and authority review.

← All articlesTechnical feedback →