Quick answer: For rainfall intensity i in mm/h, effective roof area A in m² and runoff coefficient C, Q = i × A × C / 3600 gives flow in L/s. The result alone does not select an outlet or pipe diameter. This guide connects unit conversion, catchment allocation, outlet performance and a safe overflow route.
1. What the calculation is intended to achieve
Roof rainwater design aims to convey the selected design storm to a safe outlet without unacceptable ponding. It involves more than selecting a downpipe: rainfall data, effective catchment area, gutters, outlet performance, emergency overflow, below-building drains and the discharge point must work as one system.
2. The basic flow equation
A simplified rational approach expresses design roof flow as:
- Q: rainwater flow, L/s.
- r: design rainfall intensity, L/s·m².
- A: effective roof area, m².
- C: runoff coefficient.
If intensity is supplied in mm/hour, convert it first:
One millimetre of rain over one square metre equals one litre. Omitting units can create errors as large as a factor of 3,600.
3. Selecting the design rainfall
Do not select rainfall intensity from a city name alone. Consider the weather station, storm duration, return period, data period and project risk. The Turkish State Meteorological Service publishes maximum rainfall and frequency analyses for durations including 5, 10, 15 and 30 minutes and return periods including 2, 5, 10, 25, 50 and 100 years.
Short-duration rainfall can govern small, rapidly responding roofs. Hospitals, data centres, museums and internal gutters require particular attention to risk and secondary drainage because overflow may enter the building. Determine the adopted duration and return period from applicable local requirements, the accepted standard and the project risk assessment.
4. Effective roof area
For a level roof, effective area is often close to plan area. For pitched roofs, parapets, adjoining vertical surfaces and wind-driven rain, use the effective-area method defined by the applicable standard. Each downpipe serves the catchment that actually drains to it; dividing total area by the number of pipes is not sufficient.
Mark ridges, valleys, slopes, parapet openings and outlet catchments on the drawing. Equipment plinths, solar panels and reverse falls can change flow paths.
5. Worked flow example
Assume an effective area of 600 m², design intensity of 180 mm/hour and runoff coefficient 1.0. These are educational inputs, not recommended local rainfall values.
With four equal, hydraulically balanced catchments, the preliminary allocation is 150 m² and 7.5 L/s per outlet. Final selection still requires the outlet type, water head, gutter flow, connection geometry and manufacturer's performance data.
| Parameter | Value |
|---|---|
| Effective area | 600 m² |
| Rainfall intensity | 180 mm/hour |
| Unit rainfall flow | 0.05 L/s·m² |
| Total design flow | 30 L/s |
| Theoretical flow per outlet for four equal catchments | 7.5 L/s |
6. Important gutter checks
Gutter capacity depends on cross-section, effective depth, longitudinal fall, outlet position, outlet count and freeboard. Check accumulating flow towards the outlet, not simply average flow along a long gutter. Corners, junctions, changes of direction and outlet-entry losses can reduce capacity.
Where an internal or parapet gutter can overflow into the building, do not rely on one outlet that can block. Provide an emergency overflow or an appropriately independent secondary drainage route. Visible discharge helps operators recognise a primary-system problem.
7. Selecting downpipes and horizontal drains
Downpipe performance depends on inlet geometry and flow regime as well as diameter. Conventional gravity and siphonic drainage require different methods. A siphonic network is a coordinated system designed with specialist hydraulic calculations and manufacturer data; reducing individual pipe sizes does not create one.
For horizontal drains, check fall, filling ratio, velocity, ventilation behaviour and surcharge risk. An adequate downpipe does not prove that the below-building collector or site drainage can accept its flow.
8. Primary and secondary drainage
Primary drainage carries the design storm. Secondary drainage limits unsafe water accumulation if primary outlets block or rainfall exceeds the primary design event. Coordinate secondary inlet levels with permitted ponding depth and structural roof capacity.
Do not discharge over doors, electrical rooms, façade joints or pedestrian areas. Visible overflow assists maintenance; concealed overflow can hide a failure until damage occurs.
9. Temporary storage and reuse
Rainwater storage, green roofs and controlled outlets can reduce peak discharge, but require separate volume and drawdown calculations. A reuse tank must have a safe overflow when the design storm arrives while it is already full. Sizing storage from average annual rainfall alone does not establish flood safety.
10. Design checklist
- Record the rainfall station, duration and return period.
- Show effective areas and outlet catchments on the plan.
- Confirm actual roof falls lead to outlets.
- Check that gutters, outlets and pipes convey the same design flow.
- Provide suitable independent overflow protection for internal gutters.
- Check maintenance access and leaf guards.
- Confirm below-building and site drains accept combined flow.
- Check receiving gutters and flow distribution where an upper roof drains onto a lower roof.
- Assess snow, freezing, leaves and sediment.
- Confirm discharge does not endanger foundations or neighbouring structures.
11. Common mistakes
Using daily totals instead of short-duration intensity; omitting conversion from mm/hour to L/s·m²; dividing the entire roof equally regardless of falls; overlooking contributing walls or parapets; selecting the outlet separately from the pipe; omitting overflow on internal gutters; using gravity-drainage tables for siphonic systems; ignoring collectors and site drainage; inaccessible outlets; and forgetting the full-tank overflow scenario.
12. Unit conversion and catchment allocation
When rainfall r is entered in mm/h, q=r×A×C/3,600 gives L/s. If intensity is already in L/s·m², do not divide again. Annual rainfall is not a short-duration design intensity. Show every input unit in the calculation file.
For the illustrative 600 m² roof at 180 mm/h and C=1.0, flow is 30 L/s. At an assumed 240 mm/h, it is 40 L/s. Neither value is a recommendation for a particular location: use local short-duration records, frequency, risk and the accepted method.
Four outlets carrying 7.5 L/s each are plausible only with balanced catchments and flow paths. Catchments of 100/100/100/300 m² instead require 5/5/5/15 L/s at the same rainfall intensity. Mark catchments separately and match them to outlets. A correctly sized pipe cannot prevent an overloaded inlet caused by incorrect catchment allocation. Draw the route water will take if a neighbouring outlet blocks.
13. Outlet curves and ponding depth
Connection diameter alone does not establish capacity. Grates, leaf guards and water head affect performance. Read the head at which the stated flow is achieved and compare it with the permitted roof water level. Insulation or finishes that form a dam around an outlet can cause ponding despite a correct calculation. Detail drainage at waterproofing level and at any upper drainage layer.
An average 50 mm of water over 600 m² is 30 m³, approximately 30 tonnes, or an additional load of about 0.49 kN/m². This is not a permitted structural load: it illustrates the significance of a shallow depth. Coordinate deflection, snow and equipment loads with the structural engineer. Water-induced deflection can increase ponding further.
| Scenario | Check |
|---|---|
| Design storm | Primary-system capacity |
| Blocked outlet | Transfer between catchments and emergency discharge |
| Downstream surcharge | Backwater level |
| Delayed maintenance | Leaves, sediment and access |
Set overflow levels to limit water accumulation without unnecessary discharge during normal operation. Discharge must not fall onto people, entrances or electrical equipment. A second pipe connected to the same primary drain is not automatically independent protection; apply the governing requirements for independence and capacity.
14. Siphonic drainage and storage need different calculations
Siphonic systems use dedicated outlets and full-bore flow. Check negative pressure, branch balance, pipe strength, connections and support loads through a project-specific model. Later route extensions can affect the whole network; preserve the manufacturer's design conditions.
Storage needs duration and outlet flow as well as inlet flow. If an illustrative constant inflow of 30 L/s lasts 10 minutes and outflow is 5 L/s, stored volume is (30−5)×600=15,000 litres. Real storms vary; include initial tank level and overflow. A reuse tank with no guaranteed empty volume cannot be counted automatically as flood storage. Background: https://www.geberit.co.uk/sanitary-piping-systems/water-drainage-systems/geberit-pluvia/
15. Sources and scope
- Turkish State Meteorological Service, maximum rainfall intensity and frequency analyses: https://www.mgm.gov.tr/veridegerlendirme/maksimum-yagislar.aspx
- EN 12056-3, Gravity drainage systems inside buildings — Roof drainage, layout and calculation.
- BSI, EN 12056 series: https://landingpage.bsigroup.com/LandingPage/Series?UPI=BS+EN+12056
- UK Approved Document H: https://www.gov.uk/government/publications/drainage-and-waste-disposal-approved-document-h
Verify rainfall data and the accepted standard edition for the project location. This article supports education and preliminary assessment; final design must coordinate roof construction, structural safety and site drainage under a competent engineer.
Frequently asked questions
Why divide rainfall in mm/h by 3600? One millimetre of rain over one square metre equals one litre. Dividing the hourly volume by 3600 converts it to flow per second. Do not convert again when intensity is already in L/s·m².
What is the flow for a 600 m² roof at 180 mm/h? In this educational example, C=1.0 gives Q=180×600/3600=30 L/s. The rainfall intensity is not a recommended design value for any location; use local short-duration data and the adopted design requirements for a real project.
Can total flow simply be divided by the number of outlets? No. Check each actual catchment, the outlet capacity at the available water head, gutters and pipework together. Also establish a safe overflow route for a blocked outlet.